The Tormek T-1 Kitchen Knife Sharpener is the best choice for amateur chefs when it comes to electric knife sharpeners. Unlike a simpler sharpener, a hand sharpener or a whetstone, the entire grinding phase of the knife is sharpened and not just the outer part of the cutting edge. Thanks to the patented guide, the grinding angle can be easily and precisely adjusted between 8 and 22 degrees. With the Tormek T-1 Kitchen Knife Sharpener you never have to have your knives sharpened outside the home again, but can simply sharpen them professionally in your own kitchen in just a few minutes. Tormek brand products are shipped exclusively within Germany. Delivery to other countries is not possible. Precise adjustment of the grinding angle with patented guide. For knives with blade widths of 12 - 60 mm and a thickness of up to 5 mm Grinding angle adjustable between 8 - 22 degrees on each side Housing made of precision die-cast zinc, powder-coated, base made of impact-resistant plastic, wooden handle made of solid Ash, treated with hard wax oil Cable length: 1.7 m Grinding wheel: DF-150 Conical Diamond Wheel Fine (600 grit), dimensions: Ø 150 x 18 mm Pulling wheel: PW-160 Conical composite pulling wheel Composite, ABS plastic, dimensions: Ø 160 x 30 mm Single-phase AC motor Input power: idle 60W, max. load 120W, 100-115 V / 220-240 V, 50-60 Hz Maintenance-free, smooth running, 45 dB Color: Ash Green Power: 150 rpm, torque 2 Nm Plug type: E+F Dimensions: 20.4 x 19.6 x 18.1 cm Unbalance of the grinding or honing wheel: If an imbalance occurs, try turning the diamond wheel and the honing wheel once against each other. This is a left-hand thread and no tool is required. Then turn the honing wheel a little and then tighten it again with a little momentum. As a general rule: Due to the low rotational speed, even a small unevenness or imbalance in the honing wheel looks relatively dramatic. However, this is often within the tolerance and has no influence on handling or the result. Rattling noises during operation: When the machine is delivered or has been stationary for some time, the motor shaft can leave an imprint on the drive wheel of the machine. This can lead to a recurring knocking/clacking noise. This is normal and will disappear after some time of use. It has no influence on the machine or the result.

The Tormek T-1 Kitchen Knife Sharpener is the best choice for amateur chefs when it comes to electric knife sharpeners. Unlike a simpler sharpener, a hand sharpener or a whetstone, the entire grinding phase of the knife is sharpened and not just the outer part of the cutting edge. Thanks to the patented guide, the grinding angle can be easily and precisely adjusted between 8 and 22 degrees. With the Tormek T-1 Kitchen Knife Sharpener you never have to have your knives sharpened outside the home again, but can simply sharpen them professionally in your own kitchen in just a few minutes. Tormek brand products are shipped exclusively within Germany. Delivery to other countries is not possible. Precise adjustment of the grinding angle with patented guide. For knives with blade widths of 12 - 60 mm and a thickness of up to 5 mm Grinding angle adjustable between 8 - 22 degrees on each side Housing made of precision die-cast zinc, powder-coated, base made of impact-resistant plastic, wooden handle made of solid oak, treated with hard wax oil Cable length: 1.7 m Grinding wheel: DF-150 Conical Diamond Wheel Fine (600 grit), dimensions: Ø 150 x 18 mm Pulling wheel: PW-160 Conical composite pulling wheel Composite, ABS plastic, dimensions: Ø 160 x 30 mm Single-phase AC motor Input power: idle 60W, max. load 120W, 100-115 V / 220-240 V, 50-60 Hz Maintenance-free, smooth running, 45 dB Color: Carbon Black Power: 150 rpm, torque 2 Nm Plug type: E+F Dimensions: 20.4 x 19.6 x 18.1 cm Unbalance of the grinding or honing wheel: If an imbalance occurs, try turning the diamond wheel and the honing wheel once against each other. This is a left-hand thread and no tool is required. Then turn the honing wheel a little and then tighten it again with a little momentum. As a general rule: Due to the low rotational speed, even a small unevenness or imbalance in the honing wheel looks relatively dramatic. However, this is often within the tolerance and has no influence on handling or the result. Rattling noises during operation: When the machine is delivered or has been stationary for some time, the motor shaft can leave an imprint on the drive wheel of the machine. This can lead to a recurring knocking/clacking noise. This is normal and will disappear after some time of use. It has no influence on the machine or the result.

The Tormek T-1 Kitchen Knife Sharpener is the best choice for amateur chefs when it comes to electric knife sharpeners. Unlike a simpler sharpener, a hand sharpener or a whetstone, the entire grinding phase of the knife is sharpened and not just the outer part of the cutting edge. Thanks to the patented guide, the grinding angle can be easily and precisely adjusted between 8 and 22 degrees. With the Tormek T-1 Kitchen Knife Sharpener you never have to have your knives sharpened outside the home again, but can simply sharpen them professionally in your own kitchen in just a few minutes. Tormek brand products are shipped exclusively within Germany. Delivery to other countries is not possible. Precise adjustment of the grinding angle with patented guide. For knives with blade widths of 12 - 60 mm and a thickness of up to 5 mm Grinding angle adjustable between 8 - 22 degrees on each side Housing made of precision die-cast zinc, powder-coated, base made of impact-resistant plastic, wooden handle made of solid birch, treated with hard wax oil Cable length: 1.7 m Grinding wheel: DF-150 Conical Diamond Wheel Fine (600 grit), dimensions: Ø 150 x 18 mm Pulling wheel: PW-160 Conical composite pulling wheel Composite, ABS plastic, dimensions: Ø 160 x 30 mm Single-phase AC motor Input power: idle 60W, max. load 120W, 100-115 V / 220-240 V, 50-60 Hz Maintenance-free, smooth running, 45 dB Color: Swedish Red Power: 150 rpm, torque 2 Nm Plug type: E+F Dimensions: 20.4 x 19.6 x 18.1 cm Unbalance of the grinding or honing wheel: If an imbalance occurs, try turning the diamond wheel and the honing wheel once against each other. This is a left-hand thread and no tool is required. Then turn the honing wheel a little and then tighten it again with a little momentum. As a general rule: Due to the low rotational speed, even a small unevenness or imbalance in the honing wheel looks relatively dramatic. However, this is often within the tolerance and has no influence on handling or the result. Rattling noises during operation: When the machine is delivered or has been stationary for some time, the motor shaft can leave an imprint on the drive wheel of the machine. This can lead to a recurring knocking/clacking noise. This is normal and will disappear after some time of use. It has no influence on the machine or the result.

The DF-150 Conical Diamond Wheel Fine from Tormek comes standard with the Tormek T-1 Kitchen Knife Sharpener. If the diamond grinding wheel becomes damaged or worn, it can be replaced with a new one. Tormek brand products are shipped exclusively within Germany. Delivery to other countries is not possible. Replacement grinding wheel for the Tormek T-1 Knife Sharpener 600 grit Lasts for more than a thousand grinding cycles Only suitable for the Tormek t-1 Kitchen knife Sharpener Diameter: 15 cm Width: 1.8 cm Material: Steel with diamond coating

Replacement magnet for the Tormek T-1 Kitchen Knife Sharpener. It attracts the grinding dust produced during sharpening and ensures a clean workspace. Diameter: 2 cm

The Tormek T-1 Kitchen Knife Sharpener is the best choice for amateur chefs when it comes to electric knife sharpeners. Unlike a simpler sharpener, a hand sharpener or a whetstone, the entire grinding phase of the knife is sharpened and not just the outer part of the cutting edge. Thanks to the patented guide, the grinding angle can be easily and precisely adjusted between 8 and 22 degrees. With the Tormek T-1 Kitchen Knife Sharpener you never have to have your knives sharpened outside the home again, but can simply sharpen them professionally in your own kitchen in just a few minutes. Tormek brand products are shipped exclusively within Germany. Delivery to other countries is not possible. Precise adjustment of the grinding angle with patented guide. For knives with blade widths of 12 - 60 mm and a thickness of up to 5 mm Grinding angle adjustable between 8 - 22 degrees on each side Housing made of precision die-cast zinc, powder-coated, base made of impact-resistant plastic, wooden handle made of solid oak, treated with hard wax oil Cable length: 1.7 m Grinding wheel: DF-150 Conical Diamond Wheel Fine (600 grit), dimensions: Ø 150 x 18 mm Pulling wheel: PW-160 Conical composite pulling wheel Composite, ABS plastic, dimensions: Ø 160 x 30 mm Single-phase AC motor Input power: idle 60W, max. load 120W, 100-115 V / 220-240 V, 50-60 Hz Maintenance-free, smooth running, 45 dB Color: Zinc Gray Power: 150 rpm, torque 2 Nm Plug type: E+F Dimensions: 20.4 x 19.6 x 18.1 cm Unbalance of the grinding or honing wheel: If an imbalance occurs, try turning the diamond wheel and the honing wheel once against each other. This is a left-hand thread and no tool is required. Then turn the honing wheel a little and then tighten it again with a little momentum. As a general rule: Due to the low rotational speed, even a small unevenness or imbalance in the honing wheel looks relatively dramatic. However, this is often within the tolerance and has no influence on handling or the result. Rattling noises during operation: When the machine is delivered or has been stationary for some time, the motor shaft can leave an imprint on the drive wheel of the machine. This can lead to a recurring knocking/clacking noise. This is normal and will disappear after some time of use. It has no influence on the machine or the result.